May 3, 2018

Cutter Mode Cutter Mode Note: Add the cutter baby board to J16 on the main board. Media Compartment Media Roll Shield Press the “Feed” button for 5 seconds, and the “Ready” indicator and “Power” indicator will go off in order. Slot for Extension card Close the top cover and turn on the printer or press the “FEED” button if the printer is already on.

Uploader: Kalabar
Date Added: 6 December 2010
File Size: 23.90 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 75634
Price: Free* [*Free Regsitration Required]

Load the media roll onto the hanger from left to right. Turn the wheel of the print head module to ensure the 9. Appendix I – Installing the Cutter 1. To smooth this procedure, hold the white roller with one hand.

Zebra GK d Barcode Argox os 214 plus ppla. To understand the problem, please argox os 214 plus ppla the Power and Ready LEDs and refer to the following solutions: To minimize electrical noise pickup in the cable: Caring for Your Printer Adhesives and coatings of media can over time transfer onto the printer components along the media path including the thermal print head and media sensor.

If the problem persists, replace the print head. Unwrap the dispenser kit and take out screws, the shaft, Top Cover 3. Serial Cabling Requirements Data cables must be of fully shielded construction and fitted with metal or metalized connector shells. Don’t have an account?

Media Roll Media Hanger Keep data cables short 6 ft or 1. Argox OSplus User Manual 44 pages.

Intermec PA30 Specialty Printer. Zebra SL Barcode Printer. The driver should now be installed.

Postek G Industrial Printer. Table of Contents Add to my manuals Add.

OsdOsOszOsdzOsplus. Page 26 Create a custom size In the Printers menu: Ribbon Supply Holder Ribbon Roll Media Compartment Media Hanger 3. Don’t show me this message again.

OS PLUS Bartender Sürücüsü (Driver) Kurulumu

Assign the directory to keep Seagull driver, for example: Barcode Tags Tag Solutions. Reattach the print head assembly by securing the 4 screws. This booklet is a small gift from us. Anser U2 Mobile Inkjet Printer. Press and ow the feed button while turning on the power, until the printing motor is activated.

Wheel Print Head Module Replacing the Thermal Print Head 1. Loading a Ribbon Note: Reassemble the print head module in reverse order. Remove the middle cover. Calibration and Configuration This section discusses calibration, printing configuration and resetting the printer to factory defaults.

Make sure the power switch is in the “O” position. Please refer to Appendix I. Resetting Ox to Factory Defaults 1. Trim the front edge of the label backing paper with scissors or a knife.

Ajuste de Temperatura da Cabeça de Impressão Argox | ArgoxShop

Replacing the Thermal Print Head 1. Configuration This section discusses calibration, printing configuration and resetting the printer to factory defaults. Continuous improvement of products is a policy of Argox Information Co.

Install the extension card into the printer as follows: Table Of Contents Recovery Page 3 Argox Information Co. Peeling occurs only when the argox os 214 plus ppla is properly set. Intermec PD41 Commercial Printer.

Argox OS-214 Plus

Release the screw on the left bracket of the chassis. If you are looking for an entry level label printer, or an industrial label printer, Then you will find one to suit your purpose in the Argox os 214 plus ppla label printer range. Serial rs Interface Requirements Serial RS Interface Requirements The required cable must have a nine-pin “D” type male connector on one end, which is plugged into the mating serial port located on the back of the printer. Click back the middle cover.

Parameters for Win 98 Ports In the Properties menu: Are you looking for a reliable and efficient Label printer, Then an Argox label printer may fit your budget.

0.00 avg. rating (0% score) - 0 votes